Clamps to the monitor, not the desk — 0.2 to 0.7 in
The one holder in this hub that clamps to the side of a monitor instead of a desk, with a silicone-coated cradle and a stated panel range of 0.2 to 0.7 in.
SIROLISA monitor-side clamp headset hanger
Best for: A desk with no spare edge and no spare surface, where the monitor is the only thing left to hang from.
Every other holder in this hub needs either a desk edge or a patch of desk surface. This one needs neither: it closes on the side of the monitor, left or right, which is the one vertical edge on most setups that nothing else is using. It fits without adhesive or tools.
The range follows from that and is the narrowest published here — 0.2 to 0.7 in, about 5 to 18 mm — where the desk hooks clamp onto tops from 0.31 in on the EURPMASK up to 1.97 in on the NEETTO. A thin modern panel sits comfortably inside it; a thick-bezelled older monitor or a pronounced curve may not, and SIROLISA publishes no overall size, weight or load limit for the hanger to help you judge the rest.
The cushioning claim is made as a comparison, which is unusual enough to quote: the cradle is “soft silicone-coated” to hold the headband “without damaging the headband, unlike sharp-edged stands that cause wear and scratches over time”. A curved arch with a hook at the end keeps the headband from sliding off, and the clamp itself is silicone-padded, stated to leave no marks on the monitor. At about $10 it costs the same as the Celerion desk hook.
Read on the day this page was built: $10 at the American Amazon shop.
Read from Keepa on the day this page was last revised; stock and price both move without notice.
Best for: A desk with no spare edge and no spare surface, where the monitor is the only thing left to hang from.
Prices quoted in this text were read on 2026-10-13. The live price is at the top of the page.
SIROLISA states the clamp is silicone-padded and leaves no residue or marks on removal, and that it fits panel edges of 0.2 to 0.7 in. What it does not address is the load: a heavy over-ear headset on one side of a panel pulls sideways on whatever holds the monitor up. A sturdy arm or stand copes better than a light plastic foot; check that the monitor does not lean once the headset is on.
The mounting surface, and therefore the range. The desk hooks clamp onto a desktop — the EURPMASK from 0.31 in (8 mm), the Celerion from 0.47 in (12 mm), the NEETTO up to 1.97 in (50 mm); this one closes on a monitor edge of 0.2 to 0.7 in. A desk hook will not close on a thin panel, and this will not close on most desktops.
Measure the thickness of the panel edge where you want to clamp it: SIROLISA states 0.2 to 0.7 in (5 to 18 mm). Thin modern panels usually fall inside that; a thick-bezelled older monitor or a strongly curved one may not.
A freestanding aluminum and TPU stand that publishes both its height and its base width — 8.85 in on 3.7 in square — and asks, in its own listing, for a desk that is flat and dust free.
Best for: A desk where a stand has to be moved around rather than fixed to one edge, and where the surface is flat.
A rotating spring-clamp hanger whose listing matches the Celerion hook point for point, and which reaches further down the thickness range — 0.31 in, about 8 mm, at the thin end.
Best for: A thin desktop or a glass top, where 8 mm (0.31 in) is the figure that decides it.
A spring-clamp hook that rotates 360 degrees so the headset can be turned out of the way under the desk, with a cable rack on the side and a stated clamp range of 0.47 to 1.57 in.
Best for: A desk of ordinary thickness where the headset should disappear under the edge between sessions.
A white hand-crank desk frame, 71 to 113 cm (28 to 44.5 in) tall and 102 to 160 cm (40.2 to 63 in) wide, rated 70 kg static and 50 kg dynamic — with no motor to fail, sold only in Europe.
Best for: A motor-free sit-stand desk built on a top you already own, for a buyer shopping on a European Amazon store.
Two screw-fixed metal trays, each 14.5 by 5 by 3.4 in, stated to hold up to 15 lb — the highest published capacity in this hub — screwed on, like the VIVO, so they do not rely on clamp pressure.
Best for: A standing desk you are willing to drill, where the mount must not move for years.
A clamp-on welded metal tray that fits desktops from 0.4 to 2.4 in with no drilling, rated to 10 lb, and can be mounted with its opening facing in or out.
Best for: A standing desk or a glass top, where nothing should be drilled and the tray may need to move.