Base and gooseneck in one box, and a 3/8 in thread too
A weighted metal base and a detachable gooseneck that can be used together or separately, with the only 3/8 in thread adapter on this shelf and 140 degrees of vertical travel.
Puroma metal-base stand with a gooseneck extension
Best for: A desk where the webcam sits low most days and occasionally has to reach over the monitor.
Three parts, two configurations. Used as a base and a head, this is a short stand that puts a webcam just above the desk; add the gooseneck and it reaches about 21 in, with the droop and sway any cantilever brings. Only the InnoGear overhead stand, whose boom detaches, offers a similar choice on this shelf.
The ball head is the best specified here — 360 degrees of rotation and 140 of vertical travel, where the rest of this shelf states 90 degrees or simply “multiple angles” — and it carries a 3/8 to 1/4 in thread rather than 1/4 in alone, which means a studio head, a small light or a microphone mount will fit it as well as a webcam. The base has four non-slip cotton pads underneath, stated to stop both scratches and rattle.
What the listing does not publish is a load limit, which on a stand that gains most of its reach from a gooseneck is the figure you would most want. Three stands in this hub state theirs — 1.0, 1.5 and 1.76 lb — and the reach here, at approximately 21 in, is the shortest published on the shelf.
Read on the day this page was built: $22 at the American Amazon shop.
Read from Keepa on the day this page was last revised; stock and price both move without notice.
Best for: A desk where the webcam sits low most days and occasionally has to reach over the monitor.
Prices quoted in this text were read on 2026-10-13. The live price is at the top of the page.
Studio hardware. A webcam, an action camera and a phone clamp all use a 1/4 in thread; tripod heads, light stands and microphone mounts commonly use 3/8 in. A stand that offers both can carry a studio ball head or a small light as well as a webcam, which no other listing on this shelf mentions. It is a small thing that widens what the stand can be reused for later.
No, and that is the design. The box holds a metal base, a gooseneck and a tripod head as three parts: base and head alone gives a short stand for a webcam just above the desk, and adding the gooseneck takes it to roughly 21 in with the usual cost in steadiness. The InnoGear overhead stand is the other one on this shelf that converts, by removing its boom.
The longest arm on this shelf at 36.6 in, on an aluminum-magnesium alloy core with a thickened ABS clamp — and no maximum load published anywhere.
Best for: An overhead or over-the-monitor shot that no shorter arm on this shelf can reach.
A budget plug-and-play 1080P webcam with a 6-layer glass lens, automatic exposure correction, and a digital microphone with automatic noise reduction.
Best for: A no-fuss, budget webcam for general video calls without needing driver installation.
The HP 430: a 1080p webcam with autofocus, an 85° field of view, two noise-reducing microphones, 360° pan and 15° tilt, and a built-in privacy shutter.
Best for: Frequent video calls where image sharpness, dual-mic clarity and a physical privacy shutter all matter.
The thickest published mat in this hub at 1 in, and the only one anywhere on the shelf to state a foam density — 140D high-pressure integrated molded polyurethane.
Best for: Long standing sessions, where how the foam is made matters more than what the mat is called.
One of the two thinnest mats in this hub at 13 mm (0.51 in), in PVC foam with a diamond-textured underside and a bevelled edge, sold primarily as a kitchen rug.
Best for: A short standing session on a hard floor, or the kitchen, where thickness is not the point.
The largest mat in this hub at 92 × 152 cm (36 × 60 in): a commercial-grade antistatic PVC surface over a high-density memory foam core, designed to hold its shape rather than flatten.
Best for: Genuinely long standing sessions where mat rebound and long-term shape retention matter more than price.